View MC100EL05D_714452.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
2 Input Differential AND/NAND
The MC10EL/100EL05 is a 2-input differential AND/NAND gate. The device is functionally equivalent to the E404 device with higher performance capabilities. With propagation delays and output transition times significantly faster than the E404 the EL05 is ideally suited for those applications which require the ultimate in AC performance. Because a negative 2-input NAND is equivalent to a 2-input OR function, the differential inputs and outputs of the device allows the EL05 to also be used as a 2-input differential OR/NOR gate. The differential inputs employ clamp circuitry so that under open input conditions (pulled down to VEE) the input to the AND gate will be HIGH. In this way, if one set of inputs is open, the gate will remain active to the other input.
MC10EL05 MC100EL05
8 1
* * * *
275ps Propagation Delay High Bandwidth Output Transitions 75k Internal Input Pulldown Resistors >1000V ESD Protection LOGIC DIAGRAM AND PINOUT ASSIGNMENT
D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05
D0 1 D0 2
8 VCC 7Q
PIN DESCRIPTION
D1 3
6Q
PIN D0, D1 Q
FUNCTION Data Inputs Data Outputs
D1 4
5 VEE
12/93
(c) Motorola, Inc. 1996
3-1
REV 2
MC10EL05 MC100EL05
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)
-40C Symbol IEE Characteristic Power Supply Current 10EL 100EL Power Supply Voltage 10EL 100EL Input HIGH Current -4.75 -4.20 Min Typ 18 18 -5.2 -4.5 Max 22 22 -5.5 -5.5 150 -4.75 -4.20 Min 0C Typ 18 18 -5.2 -4.5 Max 22 22 -5.5 -5.5 150 -4.75 -4.20 Min 25C Typ 18 18 -5.2 -4.5 Max 22 22 -5.5 -5.5 150 -4.75 -4.20 Min 85C Typ 18 21 -5.2 -4.5 Max 22 25 -5.5 -5.5 150 Unit
mA
VEE
V A
IIH
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)
-40C Symbol tPLH tPHL VPP VCMR tr tf Characteristic Propagation Delay to Output Minimum Input Swing1 Common Mode Range2 Output Rise/Fall Times Q (20% - 80%) Min 135 150 -0.4 100 225 See2 350 Typ 260 Max 440 Min 185 150 -0.4 100 225 See2 350 0C Typ 275 Max 390 Min 185 150 -0.4 100 225 See2 350 25C Typ 275 Max 390 Min 215 150 -0.4 100 225 See2 350 85C Typ 305 Max 420 Unit ps mV V ps
1. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of 40. 2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range is dependent on VEE and is equal to VEE + 3.0V.
MOTOROLA
3-2
ECLinPS and ECLinPS Lite DL140 -- Rev 3
MC10EL05 MC100EL05
OUTLINE DIMENSIONS
D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05 ISSUE P
-A- B
M 8 5 X 45 _
J
1 4
4X
-B-
M_ G F
NOTES: 1. DIMENSIONS A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. DIMENSIONS ARE IN MILLIMETER. 4. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 6. DIMENSION D DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50
P
0.25 (0.010)
M
-T-
8X
C
SEATING PLANE
D 0.25 (0.010)
M
K
TB
S
A
S
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
R
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
ECLinPS and ECLinPS Lite DL140 -- Rev 3 3-3
*MC10EL05/D*
MC10EL05/D MOTOROLA

▲Up To Search▲

Price & Availability of MC100EL05D

	To Download MC100EL05D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .